Stain Removal Procedure for Stone Surfaces

Stain Removal Procedure for Stone Surfaces

By Frederick M. Hueston , www.stoneforensics.com

If you find that there are some stains on your stone flooring the following stain removal information should help you remove them. A video on this procedure can also be found at http://www.youtube.com/watch?v=kh0_tUphEco

Poulticing Materials:

I have found that most stains can be classified into one of the following categories:

Oil-Based Stains: Grease, tar, cooking oil and food stains.
Organic Stains: Coffee, tea, fruit, tobacco, cosmetics, etc.
Metal Stains: Iron (rust), copper, bronze, etc.
Biological Stains: Algae, mildew, lichens, etc.
Ink Stains: Magic marker, pen, ink, etc.

There are, of course, other materials that will cause staining. These five categories are the most common.

Applying the Poultice

Once the stain is identified, the following steps can be followed:

1. Wet the stained area with distilled water. Pre-wetting fills the pores of the stone with water isolating the stain and accelerating the removal by the chemical.

2. Prepare the poultice. If a powder is to be used, pre mix the powder and the chemical of choice into a thick paste, the consistency of peanut butter. In other words, wet it enough so that it does not run. If a paper poultice is to be used, soak the paper in the chemical. Lift the paper out of the chemical until it stops dripping.

3, Apply the poultice to the stain being careful not to spill any on the non stained areas. Apply approximately 1/4-inch thick over-lapping the stain area by about one inch.

4. Cover the poultice with plastic (food wrap works great). Tape the plastic down to seal the edges. It also helps to poke several small holes in the plastic so that the powder will dry out. Failure to do this may result in the poultice staying wet.

5. Allow the poultice to dry thoroughly. This is a very important step. The drying of the poultice is what pulls the stain from the stone into the poultice material. If the poultice is not allowed to dry, the stain may not be removed. Drying usually takes from 24 to 48 hours.

6. Remove the poultice from the stain. Rinse with distilled water and buff dry with a soft cloth. If the stain is not removed, apply the poultice again. It may take up to five applications for difficult stains.

Some chemicals may etch marble and limestone surfaces. If this occurs, then apply polishing powder and buff with a piece of burlap to restore the shine.

Poulticing Powders:

Clays (Attapulgite, Kaolin, Fullers earth)  DO NOT USE OF RUST STAINS
Talc
Chalk (whiting)
Sepiolite (hydrous magnesium silicate)
Diatomaceous Earth
Methyl Cellulose
Clays and diatomaceous earth are usually the best. Do not use whiting or iron-type clays, such as Fullers Earth, with acidic chemicals. They will react with the material, canceling the effect of the poultice.

Many stains are so deeply imbedded that the poultice alone will not be completely effective. Some type of chemical solution will need to be added to the poultice. When the poultice and chemical are applied, the chemical is absorbed into the stone. The chemical reacts with the stain and is re-absorbed into the powder/material.

Stain Removing Chemicals

How do you choose the proper chemical for a given stain?

First, you need to identify the stain. This is the most important step in stain removal. If you know what caused the stain, you can easily look at a stain removal chart for the proper chemical to apply. If the stain is unknown, then you need to play detective. Try what caused the stain. If the stain is near a plant container, it might be that the plant was over watered and the soil has leached iron onto the stone. The color of the stain may help to identify the cause. Brownish color stains may be iron (rust) stains. The shape or the pattern of the stain may be helpful. Small droplet size spots leading from the coffeepot to someone's desk are a sure giveaway. Do some investigating and use your powers of observation. This will almost always lead to the identification of the cause of the stain.

If, after thorough investigation, you still have no idea what the stain is, then you will need to perform a patch test. A patch test simply means applying several chemical poultices to determine which will remove the stain.

There are also pre-prepared poultice mixes that have the chemicals already added. All you have to do is add water.

One way to reduce the amount of staining on any stone surface is to make sure it is sealed with a good penetrating sealer or impregnator.

Stain Removal Guide

Iron (rust) - Poultice with Iron Out + Powder + Water.  (Iron Out is available at hardware stores). Both mixtures may etch polished marble, so re polishing will be necessary.
Ink - Poultice with Mineral Spirits or Methylene Chloride +Powder.
Oil - Poultice with Ammonia+ Powder Methylene Chloride can also be used on tough oil stains.
Coffee, Tea & Food - Poultice with 20 percent Hydrogen Peroxide + Powder.
Copper - Poultice with Ammonium Chloride + Powder
Paint (water-based) - poultice with a commercial paint remover + Powder
Paint (oil) Poultice with Mineral Spirits + Powder. Deep stains may require Methylene Chloride.

Please use extra caution when handling all chemicals listed above. Thoroughly read Material Safety Data Sheets for each chemical before use.